/* Void Main's man pages */
{ phpMan } else { main(); }
MDADM(8) MDADM(8)
NAME
mdadm - manage MD devices aka Linux Software RAID
SYNOPSIS
mdadm [mode] <raiddevice> [options] <component-devices>
DESCRIPTION
RAID devices are virtual devices created from two or more real block devices. This allows multiple devices (typically
disk drives or partitions thereof) to be combined into a single device to hold (for example) a single filesystem. Some
RAID levels include redundancy and so can survive some degree of device failure.
Linux Software RAID devices are implemented through the md (Multiple Devices) device driver.
Currently, Linux supports LINEAR md devices, RAID0 (striping), RAID1 (mirroring), RAID4, RAID5, RAID6, RAID10, MULTIPATH,
FAULTY, and CONTAINER.
MULTIPATH is not a Software RAID mechanism, but does involve multiple devices: each device is a path to one common physi-
cal storage device. New installations should not use md/multipath as it is not well supported and has no ongoing devel-
opment. Use the Device Mapper based multipath-tools instead.
FAULTY is also not true RAID, and it only involves one device. It provides a layer over a true device that can be used
to inject faults.
CONTAINER is different again. A CONTAINER is a collection of devices that are managed as a set. This is similar to the
set of devices connected to a hardware RAID controller. The set of devices may contain a number of different RAID arrays
each utilising some (or all) of the blocks from a number of the devices in the set. For example, two devices in a
5-device set might form a RAID1 using the whole devices. The remaining three might have a RAID5 over the first half of
each device, and a RAID0 over the second half.
With a CONTAINER, there is one set of metadata that describes all of the arrays in the container. So when mdadm creates
a CONTAINER device, the device just represents the metadata. Other normal arrays (RAID1 etc) can be created inside the
container.
MODES
mdadm has several major modes of operation:
Assemble
Assemble the components of a previously created array into an active array. Components can be explicitly given or
can be searched for. mdadm checks that the components do form a bona fide array, and can, on request, fiddle
superblock information so as to assemble a faulty array.
Build Build an array that doesn't have per-device metadata (superblocks). For these sorts of arrays, mdadm cannot dif-
ferentiate between initial creation and subsequent assembly of an array. It also cannot perform any checks that
appropriate components have been requested. Because of this, the Build mode should only be used together with a
complete understanding of what you are doing.
Create Create a new array with per-device metadata (superblocks). Appropriate metadata is written to each device, and
then the array comprising those devices is activated. A 'resync' process is started to make sure that the array
is consistent (e.g. both sides of a mirror contain the same data) but the content of the device is left otherwise
untouched. The array can be used as soon as it has been created. There is no need to wait for the initial resync
to finish.
Follow or Monitor
Monitor one or more md devices and act on any state changes. This is only meaningful for RAID1, 4, 5, 6, 10 or
multipath arrays, as only these have interesting state. RAID0 or Linear never have missing, spare, or failed
drives, so there is nothing to monitor.
Grow Grow (or shrink) an array, or otherwise reshape it in some way. Currently supported growth options including
changing the active size of component devices and changing the number of active devices in RAID levels 1/4/5/6,
changing the RAID level between 1, 5, and 6, changing the chunk size and layout for RAID5 and RAID5, as well as
adding or removing a write-intent bitmap.
Incremental Assembly
Add a single device to an appropriate array. If the addition of the device makes the array runnable, the array
will be started. This provides a convenient interface to a hot-plug system. As each device is detected, mdadm
has a chance to include it in some array as appropriate. Optionally, when the --fail flag is passed in we will
remove the device from any active array instead of adding it.
If a CONTAINER is passed to mdadm in this mode, then any arrays within that container will be assembled and
started.
Manage This is for doing things to specific components of an array such as adding new spares and removing faulty devices.
Misc This is an 'everything else' mode that supports operations on active arrays, operations on component devices such
as erasing old superblocks, and information gathering operations.
Auto-detect
This mode does not act on a specific device or array, but rather it requests the Linux Kernel to activate any
auto-detected arrays.
OPTIONS
Options for selecting a mode are:
-A, --assemble
Assemble a pre-existing array.
-B, --build
Build a legacy array without superblocks.
-C, --create
Create a new array.
-F, --follow, --monitor
Select Monitor mode.
-G, --grow
Change the size or shape of an active array.
-I, --incremental
Add/remove a single device to/from an appropriate array, and possibly start the array.
--auto-detect
Request that the kernel starts any auto-detected arrays. This can only work if md is compiled into the kernel --
not if it is a module. Arrays can be auto-detected by the kernel if all the components are in primary MS-DOS par-
titions with partition type FD, and all use v0.90 metadata. In-kernel autodetect is not recommended for new
installations. Using mdadm to detect and assemble arrays -- possibly in an initrd -- is substantially more flexi-
ble and should be preferred.
If a device is given before any options, or if the first option is --add, --fail, or --remove, then the MANAGE mode is
assumed. Anything other than these will cause the Misc mode to be assumed.
Options that are not mode-specific are:
-h, --help
Display general help message or, after one of the above options, a mode-specific help message.
--help-options
Display more detailed help about command line parsing and some commonly used options.
-V, --version
Print version information for mdadm.
-v, --verbose
Be more verbose about what is happening. This can be used twice to be extra-verbose. The extra verbosity cur-
rently only affects --detail --scan and --examine --scan.
-q, --quiet
Avoid printing purely informative messages. With this, mdadm will be silent unless there is something really
important to report.
-f, --force
Be more forceful about certain operations. See the various modes for the exact meaning of this option in differ-
ent contexts.
-c, --config=
Specify the config file. Default is to use /etc/mdadm.conf, or if that is missing then /etc/mdadm/mdadm.conf. If
the config file given is partitions then nothing will be read, but mdadm will act as though the config file con-
tained exactly DEVICE partitions containers and will read /proc/partitions to find a list of devices to scan, and
/proc/mdstat to find a list of containers to examine. If the word none is given for the config file, then mdadm
will act as though the config file were empty.
-s, --scan
Scan config file or /proc/mdstat for missing information. In general, this option gives mdadm permission to get
any missing information (like component devices, array devices, array identities, and alert destination) from the
configuration file (see previous option); one exception is MISC mode when using --detail or --stop, in which case
--scan says to get a list of array devices from /proc/mdstat.
-e, --metadata=
Declare the style of RAID metadata (superblock) to be used. The default is 1.2 for --create, and to guess for
other operations. The default can be overridden by setting the metadata value for the CREATE keyword in
mdadm.conf.
Options are:
0, 0.90
Use the original 0.90 format superblock. This format limits arrays to 28 component devices and limits com-
ponent devices of levels 1 and greater to 2 terabytes.
1, 1.0, 1.1, 1.2 default
Use the new version-1 format superblock. This has few restrictions. The different sub-versions store the
superblock at different locations on the device, either at the end (for 1.0), at the start (for 1.1) or 4K
from the start (for 1.2). "1" is equivalent to "1.0". "default" is equivalent to "1.2".
ddf Use the "Industry Standard" DDF (Disk Data Format) format defined by SNIA. When creating a DDF array a
CONTAINER will be created, and normal arrays can be created in that container.
imsm Use the Intel(R) Matrix Storage Manager metadata format. This creates a CONTAINER which is managed in a
similar manner to DDF, and is supported by an option-rom on some platforms:
http://www.intel.com/design/chipsets/matrixstorage_sb.htm
--homehost=
This will override any HOMEHOST setting in the config file and provides the identity of the host which should be
considered the home for any arrays.
When creating an array, the homehost will be recorded in the metadata. For version-1 superblocks, it will be pre-
fixed to the array name. For version-0.90 superblocks, part of the SHA1 hash of the hostname will be stored in
the later half of the UUID.
When reporting information about an array, any array which is tagged for the given homehost will be reported as
such.
When using Auto-Assemble, only arrays tagged for the given homehost will be allowed to use 'local' names (i.e. not
ending in '_' followed by a digit string). See below under Auto Assembly.
For create, build, or grow:
-n, --raid-devices=
Specify the number of active devices in the array. This, plus the number of spare devices (see below) must equal
the number of component-devices (including "missing" devices) that are listed on the command line for --create.
Setting a value of 1 is probably a mistake and so requires that --force be specified first. A value of 1 will
then be allowed for linear, multipath, RAID0 and RAID1. It is never allowed for RAID4, RAID5 or RAID6.
This number can only be changed using --grow for RAID1, RAID4, RAID5 and RAID6 arrays, and only on kernels which
provide the necessary support.
-x, --spare-devices=
Specify the number of spare (eXtra) devices in the initial array. Spares can also be added and removed later.
The number of component devices listed on the command line must equal the number of RAID devices plus the number
of spare devices.
-z, --size=
Amount (in Kibibytes) of space to use from each drive in RAID levels 1/4/5/6. This must be a multiple of the
chunk size, and must leave about 128Kb of space at the end of the drive for the RAID superblock. If this is not
specified (as it normally is not) the smallest drive (or partition) sets the size, though if there is a variance
among the drives of greater than 1%, a warning is issued.
This value can be set with --grow for RAID level 1/4/5/6. If the array was created with a size smaller than the
currently active drives, the extra space can be accessed using --grow. The size can be given as max which means
to choose the largest size that fits on all current drives.
This value can not be used with CONTAINER metadata such as DDF and IMSM.
-Z, --array-size=
This is only meaningful with --grow and its effect is not persistent: when the array is stopped an restarted the
default array size will be restored.
Setting the array-size causes the array to appear smaller to programs that access the data. This is particularly
needed before reshaping an array so that it will be smaller. As the reshape is not reversible, but setting the
size with --array-size is, it is required that the array size is reduced as appropriate before the number of
devices in the array is reduced.
-c, --chunk=
Specify chunk size of kibibytes. The default when creating an array is 512KB. To ensure compatibility with ear-
lier versions, the default when Building and array with no persistent metadata is 64KB. This is only meaningful
for RAID0, RAID4, RAID5, RAID6, and RAID10.
--rounding=
Specify rounding factor for a Linear array. The size of each component will be rounded down to a multiple of this
size. This is a synonym for --chunk but highlights the different meaning for Linear as compared to other RAID
levels. The default is 64K if a kernel earlier than 2.6.16 is in use, and is 0K (i.e. no rounding) in later ker-
nels.
-l, --level=
Set RAID level. When used with --create, options are: linear, raid0, 0, stripe, raid1, 1, mirror, raid4, 4,
raid5, 5, raid6, 6, raid10, 10, multipath, mp, faulty, container. Obviously some of these are synonymous.
When a CONTAINER metadata type is requested, only the container level is permitted, and it does not need to be
explicitly given.
When used with --build, only linear, stripe, raid0, 0, raid1, multipath, mp, and faulty are valid.
Can be used with --grow to change the RAID level in some cases. See LEVEL CHANGES below.
-p, --layout=
This option configures the fine details of data layout for RAID5, RAID6, and RAID10 arrays, and controls the fail-
ure modes for faulty.
The layout of the RAID5 parity block can be one of left-asymmetric, left-symmetric, right-asymmetric, right-sym-
metric, la, ra, ls, rs. The default is left-symmetric.
It is also possibly to cause RAID5 to use a RAID4-like layout by choosing parity-first, or parity-last.
Finally for RAID5 there are DDF-compatible layouts, ddf-zero-restart, ddf-N-restart, and ddf-N-continue.
These same layouts are available for RAID6. There are also 4 layouts that will provide an intermediate stage for
converting between RAID5 and RAID6. These provide a layout which is identical to the corresponding RAID5 layout
on the first N-1 devices, and has the 'Q' syndrome (the second 'parity' block used by RAID6) on the last device.
These layouts are: left-symmetric-6, right-symmetric-6, left-asymmetric-6, right-asymmetric-6, and parity-first-6.
When setting the failure mode for level faulty, the options are: write-transient, wt, read-transient, rt,
write-persistent, wp, read-persistent, rp, write-all, read-fixable, rf, clear, flush, none.
Each failure mode can be followed by a number, which is used as a period between fault generation. Without a num-
ber, the fault is generated once on the first relevant request. With a number, the fault will be generated after
that many requests, and will continue to be generated every time the period elapses.
Multiple failure modes can be current simultaneously by using the --grow option to set subsequent failure modes.
"clear" or "none" will remove any pending or periodic failure modes, and "flush" will clear any persistent faults.
Finally, the layout options for RAID10 are one of 'n', 'o' or 'f' followed by a small number. The default is
'n2'. The supported options are:
'n' signals 'near' copies. Multiple copies of one data block are at similar offsets in different devices.
'o' signals 'offset' copies. Rather than the chunks being duplicated within a stripe, whole stripes are dupli-
cated but are rotated by one device so duplicate blocks are on different devices. Thus subsequent copies of a
block are in the next drive, and are one chunk further down.
'f' signals 'far' copies (multiple copies have very different offsets). See md(4) for more detail about 'near',
'offset', and 'far'.
The number is the number of copies of each datablock. 2 is normal, 3 can be useful. This number can be at most
equal to the number of devices in the array. It does not need to divide evenly into that number (e.g. it is per-
fectly legal to have an 'n2' layout for an array with an odd number of devices).
When an array is converted between RAID5 and RAID6 an intermediate RAID6 layout is used in which the second parity
block (Q) is always on the last device. To convert a RAID5 to RAID6 and leave it in this new layout (which does
not require re-striping) use --layout=preserve. This will try to avoid any restriping.
The converse of this is --layout=normalise which will change a non-standard RAID6 layout into a more standard
arrangement.
--parity=
same as --layout (thus explaining the p of -p).
-b, --bitmap=
Specify a file to store a write-intent bitmap in. The file should not exist unless --force is also given. The
same file should be provided when assembling the array. If the word internal is given, then the bitmap is stored
with the metadata on the array, and so is replicated on all devices. If the word none is given with --grow mode,
then any bitmap that is present is removed.
To help catch typing errors, the filename must contain at least one slash ('/') if it is a real file (not 'inter-
nal' or 'none').
Note: external bitmaps are only known to work on ext2 and ext3. Storing bitmap files on other filesystems may
result in serious problems.
--bitmap-chunk=
Set the chunksize of the bitmap. Each bit corresponds to that many Kilobytes of storage. When using a file based
bitmap, the default is to use the smallest size that is at-least 4 and requires no more than 2^21 chunks. When
using an internal bitmap, the chunksize defaults to 64Meg, or larger if necessary to fit the bitmap into the
available space.
-W, --write-mostly
subsequent devices listed in a --build, --create, or --add command will be flagged as 'write-mostly'. This is
valid for RAID1 only and means that the 'md' driver will avoid reading from these devices if at all possible.
This can be useful if mirroring over a slow link.
--write-behind=
Specify that write-behind mode should be enabled (valid for RAID1 only). If an argument is specified, it will set
the maximum number of outstanding writes allowed. The default value is 256. A write-intent bitmap is required in
order to use write-behind mode, and write-behind is only attempted on drives marked as write-mostly.
--assume-clean
Tell mdadm that the array pre-existed and is known to be clean. It can be useful when trying to recover from a
major failure as you can be sure that no data will be affected unless you actually write to the array. It can
also be used when creating a RAID1 or RAID10 if you want to avoid the initial resync, however this practice --
while normally safe -- is not recommended. Use this only if you really know what you are doing.
When the devices that will be part of a new array were filled with zeros before creation the operator knows the
array is actually clean. If that is the case, such as after running badblocks, this argument can be used to tell
mdadm the facts the operator knows.
--backup-file=
This is needed when --grow is used to increase the number of raid-devices in a RAID5 if there are no spare devices
available. See the GROW MODE section below on RAID-DEVICES CHANGES. The file should be stored on a separate
device, not on the RAID array being reshaped.
--array-size=, -Z
Set the size of the array which is seen by users of the device such as filesystems. This can be less that the
real size, but never greater. The size set this way does not persist across restarts of the array.
This is most useful when reducing the number of devices in a RAID5 or RAID6. Such arrays require the array-size
to be reduced before a reshape can be performed that reduces the real size.
A value of max restores the apparent size of the array to be whatever the real amount of available space is.
-N, --name=
Set a name for the array. This is currently only effective when creating an array with a version-1 superblock, or
an array in a DDF container. The name is a simple textual string that can be used to identify array components
when assembling. If name is needed but not specified, it is taken from the basename of the device that is being
created. e.g. when creating /dev/md/home the name will default to home.
-R, --run
Insist that mdadm run the array, even if some of the components appear to be active in another array or filesys-
tem. Normally mdadm will ask for confirmation before including such components in an array. This option causes
that question to be suppressed.
-f, --force
Insist that mdadm accept the geometry and layout specified without question. Normally mdadm will not allow cre-
ation of an array with only one device, and will try to create a RAID5 array with one missing drive (as this makes
the initial resync work faster). With --force, mdadm will not try to be so clever.
-a, --auto{=yes,md,mdp,part,p}{NN}
Instruct mdadm how to create the device file if needed, possibly allocating an unused minor number. "md" causes a
non-partitionable array to be used (though since Linux 2.6.28, these array devices are in fact partitionable).
"mdp", "part" or "p" causes a partitionable array (2.6 and later) to be used. "yes" requires the named md device
to have a 'standard' format, and the type and minor number will be determined from this. With mdadm 3.0, device
creation is normally left up to udev so this option is unlikely to be needed. See DEVICE NAMES below.
The argument can also come immediately after "-a". e.g. "-ap".
If --auto is not given on the command line or in the config file, then the default will be --auto=yes.
If --scan is also given, then any auto= entries in the config file will override the --auto instruction given on
the command line.
For partitionable arrays, mdadm will create the device file for the whole array and for the first 4 partitions. A
different number of partitions can be specified at the end of this option (e.g. --auto=p7). If the device name
ends with a digit, the partition names add a 'p', and a number, e.g. /dev/md/home1p3. If there is no trailing
digit, then the partition names just have a number added, e.g. /dev/md/scratch3.
If the md device name is in a 'standard' format as described in DEVICE NAMES, then it will be created, if neces-
sary, with the appropriate device number based on that name. If the device name is not in one of these formats,
then a unused device number will be allocated. The device number will be considered unused if there is no active
array for that number, and there is no entry in /dev for that number and with a non-standard name. Names that are
not in 'standard' format are only allowed in "/dev/md/".
For assemble:
-u, --uuid=
uuid of array to assemble. Devices which don't have this uuid are excluded
-m, --super-minor=
Minor number of device that array was created for. Devices which don't have this minor number are excluded. If
you create an array as /dev/md1, then all superblocks will contain the minor number 1, even if the array is later
assembled as /dev/md2.
Giving the literal word "dev" for --super-minor will cause mdadm to use the minor number of the md device that is
being assembled. e.g. when assembling /dev/md0, --super-minor=dev will look for super blocks with a minor number
of 0.
--super-minor is only relevant for v0.90 metadata, and should not normally be used. Using --uuid is much safer.
-N, --name=
Specify the name of the array to assemble. This must be the name that was specified when creating the array. It
must either match the name stored in the superblock exactly, or it must match with the current homehost prefixed
to the start of the given name.
-f, --force
Assemble the array even if the metadata on some devices appears to be out-of-date. If mdadm cannot find enough
working devices to start the array, but can find some devices that are recorded as having failed, then it will
mark those devices as working so that the array can be started. An array which requires --force to be started may
contain data corruption. Use it carefully.
-R, --run
Attempt to start the array even if fewer drives were given than were present last time the array was active. Nor-
mally if not all the expected drives are found and --scan is not used, then the array will be assembled but not
started. With --run an attempt will be made to start it anyway.
--no-degraded
This is the reverse of --run in that it inhibits the startup of array unless all expected drives are present.
This is only needed with --scan, and can be used if the physical connections to devices are not as reliable as you
would like.
-a, --auto{=no,yes,md,mdp,part}
See this option under Create and Build options.
-b, --bitmap=
Specify the bitmap file that was given when the array was created. If an array has an internal bitmap, there is
no need to specify this when assembling the array.
--backup-file=
If --backup-file was used to grow the number of raid-devices in a RAID5, and the system crashed during the criti-
cal section, then the same --backup-file must be presented to --assemble to allow possibly corrupted data to be
restored.
-U, --update=
Update the superblock on each device while assembling the array. The argument given to this flag can be one of
sparc2.2, summaries, uuid, name, homehost, resync, byteorder, devicesize, or super-minor.
The sparc2.2 option will adjust the superblock of an array what was created on a Sparc machine running a patched
2.2 Linux kernel. This kernel got the alignment of part of the superblock wrong. You can use the --examine
--sparc2.2 option to mdadm to see what effect this would have.
The super-minor option will update the preferred minor field on each superblock to match the minor number of the
array being assembled. This can be useful if --examine reports a different "Preferred Minor" to --detail. In
some cases this update will be performed automatically by the kernel driver. In particular the update happens
automatically at the first write to an array with redundancy (RAID level 1 or greater) on a 2.6 (or later) kernel.
The uuid option will change the uuid of the array. If a UUID is given with the --uuid option that UUID will be
used as a new UUID and will NOT be used to help identify the devices in the array. If no --uuid is given, a ran-
dom UUID is chosen.
The name option will change the name of the array as stored in the superblock. This is only supported for ver-
sion-1 superblocks.
The homehost option will change the homehost as recorded in the superblock. For version-0 superblocks, this is
the same as updating the UUID. For version-1 superblocks, this involves updating the name.
The resync option will cause the array to be marked dirty meaning that any redundancy in the array (e.g. parity
for RAID5, copies for RAID1) may be incorrect. This will cause the RAID system to perform a "resync" pass to make
sure that all redundant information is correct.
The byteorder option allows arrays to be moved between machines with different byte-order. When assembling such
an array for the first time after a move, giving --update=byteorder will cause mdadm to expect superblocks to have
their byteorder reversed, and will correct that order before assembling the array. This is only valid with origi-
nal (Version 0.90) superblocks.
The summaries option will correct the summaries in the superblock. That is the counts of total, working, active,
failed, and spare devices.
The devicesize will rarely be of use. It applies to version 1.1 and 1.2 metadata only (where the metadata is at
the start of the device) and is only useful when the component device has changed size (typically become larger).
The version 1 metadata records the amount of the device that can be used to store data, so if a device in a ver-
sion 1.1 or 1.2 array becomes larger, the metadata will still be visible, but the extra space will not. In this
case it might be useful to assemble the array with --update=devicesize. This will cause mdadm to determine the
maximum usable amount of space on each device and update the relevant field in the metadata.
For Manage mode:
-t, --test
Unless a more serious error occurred, mdadm will exit with a status of 2 if no changes were made to the array and
0 if at least one change was made. This can be useful when an indirect specifier such as missing, detached or
faulty is used in requesting an operation on the array. --test will report failure if these specifiers didn't
find any match.
-a, --add
hot-add listed devices. If a device appears to have recently been part of the array (possibly it failed or was
removed) the device is re-added as describe in the next point. If that fails or the device was never part of the
array, the device is added as a hot-spare. If the array is degraded, it will immediately start to rebuild data
onto that spare.
Note that this and the following options are only meaningful on array with redundancy. They don't apply to RAID0
or Linear.
--re-add
re-add a device that was previous removed from an array. If the metadata on the device reports that it is a mem-
ber of the array, and the slot that it used is still vacant, then the device will be added back to the array in
the same position. This will normally cause the data for that device to be recovered. However based on the event
count on the device, the recovery may only require sections that are flagged a write-intent bitmap to be recovered
or may not require any recovery at all.
When used on an array that has no metadata (i.e. it was built with --build) it will be assumed that bitmap-based
recovery is enough to make the device fully consistent with the array.
If the device name given is missing then mdadm will try to find any device that looks like it should be part of
the array but isn't and will try to re-add all such devices.
-r, --remove
remove listed devices. They must not be active. i.e. they should be failed or spare devices. As well as the
name of a device file (e.g. /dev/sda1) the words failed and detached can be given to --remove. The first causes
all failed device to be removed. The second causes any device which is no longer connected to the system (i.e an
'open' returns ENXIO) to be removed. This will only succeed for devices that are spares or have already been
marked as failed.
-f, --fail
mark listed devices as faulty. As well as the name of a device file, the word detached can be given. This will
cause any device that has been detached from the system to be marked as failed. It can then be removed.
--set-faulty
same as --fail.
--write-mostly
Subsequent devices that are added or re-added will have the 'write-mostly' flag set. This is only valid for RAID1
and means that the 'md' driver will avoid reading from these devices if possible.
--readwrite
Subsequent devices that are added or re-added will have the 'write-mostly' flag cleared.
Each of these options requires that the first device listed is the array to be acted upon, and the remainder are compo-
nent devices to be added, removed, marked as faulty, etc. Several different operations can be specified for different
devices, e.g.
mdadm /dev/md0 --add /dev/sda1 --fail /dev/sdb1 --remove /dev/sdb1
Each operation applies to all devices listed until the next operation.
If an array is using a write-intent bitmap, then devices which have been removed can be re-added in a way that avoids a
full reconstruction but instead just updates the blocks that have changed since the device was removed. For arrays with
persistent metadata (superblocks) this is done automatically. For arrays created with --build mdadm needs to be told
that this device we removed recently with --re-add.
Devices can only be removed from an array if they are not in active use, i.e. that must be spares or failed devices. To
remove an active device, it must first be marked as faulty.
For Misc mode:
-Q, --query
Examine a device to see (1) if it is an md device and (2) if it is a component of an md array. Information about
what is discovered is presented.
-D, --detail
Print details of one or more md devices.
--detail-platform
Print details of the platform's RAID capabilities (firmware / hardware topology) for a given metadata format.
-Y, --export
When used with --detail or --examine, output will be formatted as key=value pairs for easy import into the envi-
ronment.
-E, --examine
Print contents of the metadata stored on the named device(s). Note the contrast between --examine and --detail.
--examine applies to devices which are components of an array, while --detail applies to a whole array which is
currently active.
--sparc2.2
If an array was created on a SPARC machine with a 2.2 Linux kernel patched with RAID support, the superblock will
have been created incorrectly, or at least incompatibly with 2.4 and later kernels. Using the --sparc2.2 flag
with --examine will fix the superblock before displaying it. If this appears to do the right thing, then the
array can be successfully assembled using --assemble --update=sparc2.2.
-X, --examine-bitmap
Report information about a bitmap file. The argument is either an external bitmap file or an array component in
case of an internal bitmap. Note that running this on an array device (e.g. /dev/md0) does not report the bitmap
for that array.
-R, --run
start a partially assembled array. If --assemble did not find enough devices to fully start the array, it might
leaving it partially assembled. If you wish, you can then use --run to start the array in degraded mode.
-S, --stop
deactivate array, releasing all resources.
-o, --readonly
mark array as readonly.
-w, --readwrite
mark array as readwrite.
--zero-superblock
If the device contains a valid md superblock, the block is overwritten with zeros. With --force the block where
the superblock would be is overwritten even if it doesn't appear to be valid.
--kill-subarray=
If the device is a container and the argument to --kill-subarray specifies an inactive subarray in the container,
then the subarray is deleted. Deleting all subarrays will leave an 'empty-container' or spare superblock on the
drives. See --zero-superblock for completely removing a superblock. Note that some formats depend on the subar-
ray index for generating a UUID, this command will fail if it would change the UUID of an active subarray.
--update-subarray=
If the device is a container and the argument to --update-subarray specifies a subarray in the container, then
attempt to update the given superblock field in the subarray. See below in MISC MODE for details.
-t, --test
When used with --detail, the exit status of mdadm is set to reflect the status of the device. See below in MISC
MODE for details.
-W, --wait
For each md device given, wait for any resync, recovery, or reshape activity to finish before returning. mdadm
will return with success if it actually waited for every device listed, otherwise it will return failure.
--wait-clean
For each md device given, or each device in /proc/mdstat if --scan is given, arrange for the array to be marked
clean as soon as possible. mdadm will return with success if the array uses external metadata and we successfully
waited. For native arrays this returns immediately as the kernel handles dirty-clean transitions at shutdown. No
action is taken if safe-mode handling is disabled.
For Incremental Assembly mode:
--rebuild-map, -r
Rebuild the map file (/var/run/mdadm/map) that mdadm uses to help track which arrays are currently being assem-
bled.
--run, -R
Run any array assembled as soon as a minimal number of devices are available, rather than waiting until all
expected devices are present.
--scan, -s
Only meaningful with -R this will scan the map file for arrays that are being incrementally assembled and will try
to start any that are not already started. If any such array is listed in mdadm.conf as requiring an external
bitmap, that bitmap will be attached first.
--fail, -f
This allows the hot-plug system to remove devices that have fully disappeared from the kernel. It will first fail
and then remove the device from any array it belongs to. The device name given should be a kernel device name
such as "sda", not a name in /dev.
For Monitor mode:
-m, --mail
Give a mail address to send alerts to.
-p, --program, --alert
Give a program to be run whenever an event is detected.
-y, --syslog
Cause all events to be reported through 'syslog'. The messages have facility of 'daemon' and varying priorities.
-d, --delay
Give a delay in seconds. mdadm polls the md arrays and then waits this many seconds before polling again. The
default is 60 seconds. Since 2.6.16, there is no need to reduce this as the kernel alerts mdadm immediately when
there is any change.
-r, --increment
Give a percentage increment. mdadm will generate RebuildNN events with the given percentage increment.
-f, --daemonise
Tell mdadm to run as a background daemon if it decides to monitor anything. This causes it to fork and run in the
child, and to disconnect from the terminal. The process id of the child is written to stdout. This is useful
with --scan which will only continue monitoring if a mail address or alert program is found in the config file.
-i, --pid-file
When mdadm is running in daemon mode, write the pid of the daemon process to the specified file, instead of print-
ing it on standard output.
-1, --oneshot
Check arrays only once. This will generate NewArray events and more significantly DegradedArray and SparesMissing
events. Running
mdadm --monitor --scan -1
from a cron script will ensure regular notification of any degraded arrays.
-t, --test
Generate a TestMessage alert for every array found at startup. This alert gets mailed and passed to the alert
program. This can be used for testing that alert message do get through successfully.
ASSEMBLE MODE
Usage: mdadm --assemble md-device options-and-component-devices...
Usage: mdadm --assemble --scan md-devices-and-options...
Usage: mdadm --assemble --scan options...
This usage assembles one or more RAID arrays from pre-existing components. For each array, mdadm needs to know the md
device, the identity of the array, and a number of component-devices. These can be found in a number of ways.
In the first usage example (without the --scan) the first device given is the md device. In the second usage example,
all devices listed are treated as md devices and assembly is attempted. In the third (where no devices are listed) all
md devices that are listed in the configuration file are assembled. If not arrays are described by the configuration
file, then any arrays that can be found on unused devices will be assembled.
If precisely one device is listed, but --scan is not given, then mdadm acts as though --scan was given and identity
information is extracted from the configuration file.
The identity can be given with the --uuid option, the --name option, or the --super-minor option, will be taken from the
md-device record in the config file, or will be taken from the super block of the first component-device listed on the
command line.
Devices can be given on the --assemble command line or in the config file. Only devices which have an md superblock
which contains the right identity will be considered for any array.
The config file is only used if explicitly named with --config or requested with (a possibly implicit) --scan. In the
later case, /etc/mdadm.conf or /etc/mdadm/mdadm.conf is used.
If --scan is not given, then the config file will only be used to find the identity of md arrays.
Normally the array will be started after it is assembled. However if --scan is not given and not all expected drives
were listed, then the array is not started (to guard against usage errors). To insist that the array be started in this
case (as may work for RAID1, 4, 5, 6, or 10), give the --run flag.
If udev is active, mdadm does not create any entries in /dev but leaves that to udev. It does record information in
/var/run/mdadm/map which will allow udev to choose the correct name.
If mdadm detects that udev is not configured, it will create the devices in /dev itself.
In Linux kernels prior to version 2.6.28 there were two distinctly different types of md devices that could be created:
one that could be partitioned using standard partitioning tools and one that could not. Since 2.6.28 that distinction is
no longer relevant as both type of devices can be partitioned. mdadm will normally create the type that originally could
not be partitioned as it has a well defined major number (9).
Prior to 2.6.28, it is important that mdadm chooses the correct type of array device to use. This can be controlled with
the --auto option. In particular, a value of "mdp" or "part" or "p" tells mdadm to use a partitionable device rather
than the default.
In the no-udev case, the value given to --auto can be suffixed by a number. This tells mdadm to create that number of
partition devices rather than the default of 4.
The value given to --auto can also be given in the configuration file as a word starting auto= on the ARRAY line for the
relevant array.
Auto Assembly
When --assemble is used with --scan and no devices are listed, mdadm will first attempt to assemble all the arrays listed
in the config file.
In no array at listed in the config (other than those marked <ignore>) it will look through the available devices for
possible arrays and will try to assemble anything that it finds. Arrays which are tagged as belonging to the given home-
host will be assembled and started normally. Arrays which do not obviously belong to this host are given names that are
expected not to conflict with anything local, and are started "read-auto" so that nothing is written to any device until
the array is written to. i.e. automatic resync etc is delayed.
If mdadm finds a consistent set of devices that look like they should comprise an array, and if the superblock is tagged
as belonging to the given home host, it will automatically choose a device name and try to assemble the array. If the
array uses version-0.90 metadata, then the minor number as recorded in the superblock is used to create a name in
/dev/md/ so for example /dev/md/3. If the array uses version-1 metadata, then the name from the superblock is used to
similarly create a name in /dev/md/ (the name will have any 'host' prefix stripped first).
This behaviour can be modified by the AUTO line in the mdadm.conf configuration file. This line can indicate that spe-
cific metadata type should, or should not, be automatically assembled. If an array is found which is not listed in
mdadm.conf and has a metadata format that is denied by the AUTO line, then it will not be assembled. The AUTO line can
also request that all arrays identified as being for this homehost should be assembled regardless of their metadata type.
See mdadm.conf(5) for further details.
BUILD MODE
Usage: mdadm --build md-device --chunk=X --level=Y --raid-devices=Z devices
This usage is similar to --create. The difference is that it creates an array without a superblock. With these arrays
there is no difference between initially creating the array and subsequently assembling the array, except that hopefully
there is useful data there in the second case.
The level may raid0, linear, raid1, raid10, multipath, or faulty, or one of their synonyms. All devices must be listed
and the array will be started once complete. It will often be appropriate to use --assume-clean with levels raid1 or
raid10.
CREATE MODE
Usage: mdadm --create md-device --chunk=X --level=Y
--raid-devices=Z devices
This usage will initialise a new md array, associate some devices with it, and activate the array.
The named device will normally not exist when mdadm --create is run, but will be created by udev once the array becomes
active.
As devices are added, they are checked to see if they contain RAID superblocks or filesystems. They are also checked to
see if the variance in device size exceeds 1%.
If any discrepancy is found, the array will not automatically be run, though the presence of a --run can override this
caution.
To create a "degraded" array in which some devices are missing, simply give the word "missing" in place of a device name.
This will cause mdadm to leave the corresponding slot in the array empty. For a RAID4 or RAID5 array at most one slot
can be "missing"; for a RAID6 array at most two slots. For a RAID1 array, only one real device needs to be given. All
of the others can be "missing".
When creating a RAID5 array, mdadm will automatically create a degraded array with an extra spare drive. This is because
building the spare into a degraded array is in general faster than resyncing the parity on a non-degraded, but not clean,
array. This feature can be overridden with the --force option.
When creating an array with version-1 metadata a name for the array is required. If this is not given with the --name
option, mdadm will choose a name based on the last component of the name of the device being created. So if /dev/md3 is
being created, then the name 3 will be chosen. If /dev/md/home is being created, then the name home will be used.
When creating a partition based array, using mdadm with version-1.x metadata, the partition type should be set to 0xDA
(non fs-data). This type selection allows for greater precision since using any other [RAID auto-detect (0xFD) or a
GNU/Linux partition (0x83)], might create problems in the event of array recovery through a live cdrom.
A new array will normally get a randomly assigned 128bit UUID which is very likely to be unique. If you have a specific
need, you can choose a UUID for the array by giving the --uuid= option. Be warned that creating two arrays with the same
UUID is a recipe for disaster. Also, using --uuid= when creating a v0.90 array will silently override any --homehost=
setting.
When creating an array within a CONTAINER mdadm can be given either the list of devices to use, or simply the name of the
container. The former case gives control over which devices in the container will be used for the array. The latter
case allows mdadm to automatically choose which devices to use based on how much spare space is available.
The General Management options that are valid with --create are:
--run insist on running the array even if some devices look like they might be in use.
--readonly
start the array readonly -- not supported yet.
MANAGE MODE
Usage: mdadm device options... devices...
This usage will allow individual devices in an array to be failed, removed or added. It is possible to perform multiple
operations with on command. For example:
mdadm /dev/md0 -f /dev/hda1 -r /dev/hda1 -a /dev/hda1
will firstly mark /dev/hda1 as faulty in /dev/md0 and will then remove it from the array and finally add it back in as a
spare. However only one md array can be affected by a single command.
When a device is added to an active array, mdadm checks to see if it has metadata on it which suggests that it was
recently a member of the array. If it does, it tries to "re-add" the device. If there have been no changes since the
device was removed, or if the array has a write-intent bitmap which has recorded whatever changes there were, then the
device will immediately become a full member of the array and those differences recorded in the bitmap will be resolved.
MISC MODE
Usage: mdadm options ... devices ...
MISC mode includes a number of distinct operations that operate on distinct devices. The operations are:
--query
The device is examined to see if it is (1) an active md array, or (2) a component of an md array. The information
discovered is reported.
--detail
The device should be an active md device. mdadm will display a detailed description of the array. --brief or
--scan will cause the output to be less detailed and the format to be suitable for inclusion in /etc/mdadm.conf.
The exit status of mdadm will normally be 0 unless mdadm failed to get useful information about the device(s);
however, if the --test option is given, then the exit status will be:
0 The array is functioning normally.
1 The array has at least one failed device.
2 The array has multiple failed devices such that it is unusable.
4 There was an error while trying to get information about the device.
--detail-platform
Print detail of the platform's RAID capabilities (firmware / hardware topology). If the metadata is specified
with -e or --metadata= then the return status will be:
0 metadata successfully enumerated its platform components on this system
1 metadata is platform independent
2 metadata failed to find its platform components on this system
--update-subarray=
If the device is a container and the argument to --update-subarray specifies a subarray in the container, then
attempt to update the given superblock field in the subarray. Similar to updating an array in "assemble" mode,
the field to update is selected by -U or --update= option. Currently only name is supported.
The name option updates the subarray name in the metadata, it may not affect the device node name or the device
node symlink until the subarray is re-assembled. If updating name would change the UUID of an active subarray
this operation is blocked, and the command will end in an error.
--examine
The device should be a component of an md array. mdadm will read the md superblock of the device and display the
contents. If --brief or --scan is given, then multiple devices that are components of the one array are grouped
together and reported in a single entry suitable for inclusion in /etc/mdadm.conf.
Having --scan without listing any devices will cause all devices listed in the config file to be examined.
--stop The devices should be active md arrays which will be deactivated, as long as they are not currently in use.
--run This will fully activate a partially assembled md array.
--readonly
This will mark an active array as read-only, providing that it is not currently being used.
--readwrite
This will change a readonly array back to being read/write.
--scan For all operations except --examine, --scan will cause the operation to be applied to all arrays listed in
/proc/mdstat. For --examine, --scan causes all devices listed in the config file to be examined.
-b, --brief
Be less verbose. This is used with --detail and --examine. Using --brief with --verbose gives an intermediate
level of verbosity.
MONITOR MODE
Usage: mdadm --monitor options... devices...
This usage causes mdadm to periodically poll a number of md arrays and to report on any events noticed. mdadm will never
exit once it decides that there are arrays to be checked, so it should normally be run in the background.
As well as reporting events, mdadm may move a spare drive from one array to another if they are in the same spare-group
and if the destination array has a failed drive but no spares.
If any devices are listed on the command line, mdadm will only monitor those devices. Otherwise all arrays listed in the
configuration file will be monitored. Further, if --scan is given, then any other md devices that appear in /proc/mdstat
will also be monitored.
The result of monitoring the arrays is the generation of events. These events are passed to a separate program (if spec-
ified) and may be mailed to a given E-mail address.
When passing events to a program, the program is run once for each event, and is given 2 or 3 command-line arguments: the
first is the name of the event (see below), the second is the name of the md device which is affected, and the third is
the name of a related device if relevant (such as a component device that has failed).
If --scan is given, then a program or an E-mail address must be specified on the command line or in the config file. If
neither are available, then mdadm will not monitor anything. Without --scan, mdadm will continue monitoring as long as
something was found to monitor. If no program or email is given, then each event is reported to stdout.
The different events are:
DeviceDisappeared
An md array which previously was configured appears to no longer be configured. (syslog priority: Critical)
If mdadm was told to monitor an array which is RAID0 or Linear, then it will report DeviceDisappeared with the
extra information Wrong-Level. This is because RAID0 and Linear do not support the device-failed, hot-spare
and resync operations which are monitored.
RebuildStarted
An md array started reconstruction. (syslog priority: Warning)
RebuildNN
Where NN is a two-digit number (ie. 05, 48). This indicates that rebuild has passed that many percent of the
total. The events are generated with fixed increment since 0. Increment size may be specified with a command-
line option (default is 20). (syslog priority: Warning)
RebuildFinished
An md array that was rebuilding, isn't any more, either because it finished normally or was aborted. (syslog
priority: Warning)
Fail An active component device of an array has been marked as faulty. (syslog priority: Critical)
FailSpare
A spare component device which was being rebuilt to replace a faulty device has failed. (syslog priority:
Critical)
SpareActive
A spare component device which was being rebuilt to replace a faulty device has been successfully rebuilt and
has been made active. (syslog priority: Info)
NewArray
A new md array has been detected in the /proc/mdstat file. (syslog priority: Info)
DegradedArray
A newly noticed array appears to be degraded. This message is not generated when mdadm notices a drive fail-
ure which causes degradation, but only when mdadm notices that an array is degraded when it first sees the
array. (syslog priority: Critical)
MoveSpare
A spare drive has been moved from one array in a spare-group to another to allow a failed drive to be
replaced. (syslog priority: Info)
SparesMissing
If mdadm has been told, via the config file, that an array should have a certain number of spare devices, and
mdadm detects that it has fewer than this number when it first sees the array, it will report a SparesMissing
message. (syslog priority: Warning)
TestMessage
An array was found at startup, and the --test flag was given. (syslog priority: Info)
Only Fail, FailSpare, DegradedArray, SparesMissing and TestMessage cause Email to be sent. All events cause the program
to be run. The program is run with two or three arguments: the event name, the array device and possibly a second
device.
Each event has an associated array device (e.g. /dev/md1) and possibly a second device. For Fail, FailSpare, and Spare-
Active the second device is the relevant component device. For MoveSpare the second device is the array that the spare
was moved from.
For mdadm to move spares from one array to another, the different arrays need to be labeled with the same spare-group in
the configuration file. The spare-group name can be any string; it is only necessary that different spare groups use
different names.
When mdadm detects that an array in a spare group has fewer active devices than necessary for the complete array, and has
no spare devices, it will look for another array in the same spare group that has a full complement of working drive and
a spare. It will then attempt to remove the spare from the second drive and add it to the first. If the removal suc-
ceeds but the adding fails, then it is added back to the original array.
GROW MODE
The GROW mode is used for changing the size or shape of an active array. For this to work, the kernel must support the
necessary change. Various types of growth are being added during 2.6 development, including restructuring a RAID5 array
to have more active devices.
Currently the only support available is to
o change the "size" attribute for RAID1, RAID5 and RAID6.
o increase or decrease the "raid-devices" attribute of RAID1, RAID5, and RAID6.
change the chunk-size and layout of RAID5 and RAID6.
convert between RAID1 and RAID5, and between RAID5 and RAID6.
o add a write-intent bitmap to any array which supports these bitmaps, or remove a write-intent bitmap from such an
array.
GROW mode is not currently supported for CONTAINERS or arrays inside containers.
SIZE CHANGES
Normally when an array is built the "size" it taken from the smallest of the drives. If all the small drives in an
arrays are, one at a time, removed and replaced with larger drives, then you could have an array of large drives with
only a small amount used. In this situation, changing the "size" with "GROW" mode will allow the extra space to start
being used. If the size is increased in this way, a "resync" process will start to make sure the new parts of the array
are synchronised.
Note that when an array changes size, any filesystem that may be stored in the array will not automatically grow to use
the space. The filesystem will need to be explicitly told to use the extra space.
Also the size of an array cannot be changed while it has an active bitmap. If an array has a bitmap, it must be removed
before the size can be changed. Once the change it complete a new bitmap can be created.
RAID-DEVICES CHANGES
A RAID1 array can work with any number of devices from 1 upwards (though 1 is not very useful). There may be times which
you want to increase or decrease the number of active devices. Note that this is different to hot-add or hot-remove
which changes the number of inactive devices.
When reducing the number of devices in a RAID1 array, the slots which are to be removed from the array must already be
vacant. That is, the devices which were in those slots must be failed and removed.
When the number of devices is increased, any hot spares that are present will be activated immediately.
Changing the number of active devices in a RAID5 or RAID6 is much more effort. Every block in the array will need to be
read and written back to a new location. From 2.6.17, the Linux Kernel is able to increase the number of devices in a
RAID5 safely, including restarting an interrupted "reshape". From 2.6.31, the Linux Kernel is able to increase or
decrease the number of devices in a RAID5 or RAID6.
When decreasing the number of devices, the size of the array will also decrease. If there was data in the array, it
could get destroyed and this is not reversible. To help prevent accidents, mdadm requires that the size of the array be
decreased first with mdadm --grow --array-size. This is a reversible change which simply makes the end of the array
inaccessible. The integrity of any data can then be checked before the non-reversible reduction in the number of devices
is request.
When relocating the first few stripes on a RAID5, it is not possible to keep the data on disk completely consistent and
crash-proof. To provide the required safety, mdadm disables writes to the array while this "critical section" is
reshaped, and takes a backup of the data that is in that section. This backup is normally stored in any spare devices
that the array has, however it can also be stored in a separate file specified with the --backup-file option. If this
option is used, and the system does crash during the critical period, the same file must be passed to --assemble to
restore the backup and reassemble the array.
LEVEL CHANGES
Changing the RAID level of any array happens instantaneously. However in the RAID to RAID6 case this requires a non-
standard layout of the RAID6 data, and in the RAID6 to RAID5 case that non-standard layout is required before the change
can be accomplish. So while the level change is instant, the accompanying layout change can take quite a long time.
CHUNK-SIZE AND LAYOUT CHANGES
Changing the chunk-size of layout without also changing the number of devices as the same time will involve re-writing
all blocks in-place. To ensure against data loss in the case of a crash, a --backup-file must be provided for these
changes. Small sections of the array will be copied to the backup file while they are being rearranged.
If the reshape is interrupted for any reason, this backup file must be make available to mdadm --assemble so the array
can be reassembled. Consequently the file cannot be stored on the device being reshaped.
BITMAP CHANGES
A write-intent bitmap can be added to, or removed from, an active array. Either internal bitmaps, or bitmaps stored in a
separate file, can be added. Note that if you add a bitmap stored in a file which is in a filesystem that is on the RAID
array being affected, the system will deadlock. The bitmap must be on a separate filesystem.
INCREMENTAL MODE
Usage: mdadm --incremental [--run] [--quiet] component-device
Usage: mdadm --incremental --fail component-device
Usage: mdadm --incremental --rebuild-map
Usage: mdadm --incremental --run --scan
This mode is designed to be used in conjunction with a device discovery system. As devices are found in a system, they
can be passed to mdadm --incremental to be conditionally added to an appropriate array.
Conversely, it can also be used with the --fail flag to do just the opposite and find whatever array a particular device
is part of and remove the device from that array.
If the device passed is a CONTAINER device created by a previous call to mdadm, then rather than trying to add that
device to an array, all the arrays described by the metadata of the container will be started.
mdadm performs a number of tests to determine if the device is part of an array, and which array it should be part of.
If an appropriate array is found, or can be created, mdadm adds the device to the array and conditionally starts the
array.
Note that mdadm will only add devices to an array which were previously working (active or spare) parts of that array.
It does not currently support automatic inclusion of a new drive as a spare in some array.
The tests that mdadm makes are as follow:
+ Is the device permitted by mdadm.conf? That is, is it listed in a DEVICES line in that file. If DEVICES is
absent then the default it to allow any device. Similar if DEVICES contains the special word partitions then any
device is allowed. Otherwise the device name given to mdadm must match one of the names or patterns in a DEVICES
line.
+ Does the device have a valid md superblock. If a specific metadata version is request with --metadata or -e then
only that style of metadata is accepted, otherwise mdadm finds any known version of metadata. If no md metadata
is found, the device is rejected.
mdadm keeps a list of arrays that it has partially assembled in /var/run/mdadm/map (or /var/run/mdadm.map if the
directory doesn't exist. Or maybe even /dev/.mdadm.map). If no array exists which matches the metadata on the
new device, mdadm must choose a device name and unit number. It does this based on any name given in mdadm.conf
or any name information stored in the metadata. If this name suggests a unit number, that number will be used,
otherwise a free unit number will be chosen. Normally mdadm will prefer to create a partitionable array, however
if the CREATE line in mdadm.conf suggests that a non-partitionable array is preferred, that will be honoured.
If the array is not found in the config file and its metadata does not identify it as belonging to the "homehost",
then mdadm will choose a name for the array which is certain not to conflict with any array which does belong to
this host. It does this be adding an underscore and a small number to the name preferred by the metadata.
Once an appropriate array is found or created and the device is added, mdadm must decide if the array is ready to
be started. It will normally compare the number of available (non-spare) devices to the number of devices that
the metadata suggests need to be active. If there are at least that many, the array will be started. This means
that if any devices are missing the array will not be restarted.
As an alternative, --run may be passed to mdadm in which case the array will be run as soon as there are enough
devices present for the data to be accessible. For a RAID1, that means one device will start the array. For a
clean RAID5, the array will be started as soon as all but one drive is present.
Note that neither of these approaches is really ideal. If it can be known that all device discovery has com-
pleted, then
mdadm -IRs
can be run which will try to start all arrays that are being incrementally assembled. They are started in "read-
auto" mode in which they are read-only until the first write request. This means that no metadata updates are
made and no attempt at resync or recovery happens. Further devices that are found before the first write can
still be added safely.
ENVIRONMENT
This section describes environment variables that affect how mdadm operates.
MDADM_NO_MDMON
Setting this value to 1 will prevent mdadm from automatically launching mdmon. This variable is intended primar-
ily for debugging mdadm/mdmon.
MDADM_NO_UDEV
Normally, mdadm does not create any device nodes in /dev, but leaves that task to udev. If udev appears not to be
configured, or if this environment variable is set to '1', the mdadm will create and devices that are needed.
EXAMPLES
mdadm --query /dev/name-of-device
This will find out if a given device is a RAID array, or is part of one, and will provide brief information about the
device.
mdadm --assemble --scan
This will assemble and start all arrays listed in the standard config file. This command will typically go in a system
startup file.
mdadm --stop --scan
This will shut down all arrays that can be shut down (i.e. are not currently in use). This will typically go in a system
shutdown script.
mdadm --follow --scan --delay=120
If (and only if) there is an Email address or program given in the standard config file, then monitor the status of all
arrays listed in that file by polling them ever 2 minutes.
mdadm --create /dev/md0 --level=1 --raid-devices=2 /dev/hd[ac]1
Create /dev/md0 as a RAID1 array consisting of /dev/hda1 and /dev/hdc1.
echo 'DEVICE /dev/hd*[0-9] /dev/sd*[0-9]' > mdadm.conf
mdadm --detail --scan >> mdadm.conf
This will create a prototype config file that describes currently active arrays that are known to be made from partitions
of IDE or SCSI drives. This file should be reviewed before being used as it may contain unwanted detail.
echo 'DEVICE /dev/hd[a-z] /dev/sd*[a-z]' > mdadm.conf
mdadm --examine --scan --config=mdadm.conf >> mdadm.conf
This will find arrays which could be assembled from existing IDE and SCSI whole drives (not partitions), and store the
information in the format of a config file. This file is very likely to contain unwanted detail, particularly the
devices= entries. It should be reviewed and edited before being used as an actual config file.
mdadm --examine --brief --scan --config=partitions
mdadm -Ebsc partitions
Create a list of devices by reading /proc/partitions, scan these for RAID superblocks, and printout a brief listing of
all that were found.
mdadm -Ac partitions -m 0 /dev/md0
Scan all partitions and devices listed in /proc/partitions and assemble /dev/md0 out of all such devices with a RAID
superblock with a minor number of 0.
mdadm --monitor --scan --daemonise > /var/run/mdadm
If config file contains a mail address or alert program, run mdadm in the background in monitor mode monitoring all md
devices. Also write pid of mdadm daemon to /var/run/mdadm.
mdadm -Iq /dev/somedevice
Try to incorporate newly discovered device into some array as appropriate.
mdadm --incremental --rebuild-map --run --scan
Rebuild the array map from any current arrays, and then start any that can be started.
mdadm /dev/md4 --fail detached --remove detached
Any devices which are components of /dev/md4 will be marked as faulty and then remove from the array.
mdadm --grow /dev/md4 --level=6 --backup-file=/root/backup-md4
The array /dev/md4 which is currently a RAID5 array will be converted to RAID6. There should normally already be a spare
drive attached to the array as a RAID6 needs one more drive than a matching RAID5.
mdadm --create /dev/md/ddf --metadata=ddf --raid-disks 6 /dev/sd[a-f]
Create a DDF array over 6 devices.
mdadm --create /dev/md/home -n3 -l5 -z 30000000 /dev/md/ddf
Create a RAID5 array over any 3 devices in the given DDF set. Use only 30 gigabytes of each device.
mdadm -A /dev/md/ddf1 /dev/sd[a-f]
Assemble a pre-exist ddf array.
mdadm -I /dev/md/ddf1
Assemble all arrays contained in the ddf array, assigning names as appropriate.
mdadm --create --help
Provide help about the Create mode.
mdadm --config --help
Provide help about the format of the config file.
mdadm --help
Provide general help.
FILES
/proc/mdstat
If you're using the /proc filesystem, /proc/mdstat lists all active md devices with information about them. mdadm uses
this to find arrays when --scan is given in Misc mode, and to monitor array reconstruction on Monitor mode.
/etc/mdadm.conf
The config file lists which devices may be scanned to see if they contain MD super block, and gives identifying informa-
tion (e.g. UUID) about known MD arrays. See mdadm.conf(5) for more details.
/var/run/mdadm/map
When --incremental mode is used, this file gets a list of arrays currently being created. If /var/run/mdadm does not
exist as a directory, then /var/run/mdadm.map is used instead. If /var/run is not available (as may be the case during
early boot), /dev/.mdadm.map is used on the basis that /dev is usually available very early in boot.
DEVICE NAMES
mdadm understand two sorts of names for array devices.
The first is the so-called 'standard' format name, which matches the names used by the kernel and which appear in
/proc/mdstat.
The second sort can be freely chosen, but must reside in /dev/md/. When giving a device name to mdadm to create or
assemble an array, either full path name such as /dev/md0 or /dev/md/home can be given, or just the suffix of the second
sort of name, such as home can be given.
When mdadm chooses device names during auto-assembly or incremental assembly, it will sometimes add a small sequence num-
ber to the end of the name to avoid conflicted between multiple arrays that have the same name. If mdadm can reasonably
determine that the array really is meant for this host, either by a hostname in the metadata, or by the presence of the
array in /etc/mdadm.conf, then it will leave off the suffix if possible. Also if the homehost is specified as <ignore>
mdadm will only use a suffix if a different array of the same name already exists or is listed in the config file.
The standard names for non-partitioned arrays (the only sort of md array available in 2.4 and earlier) are of the form
/dev/mdNN
where NN is a number. The standard names for partitionable arrays (as available from 2.6 onwards) are of the form
/dev/md_dNN
Partition numbers should be indicated by added "pMM" to these, thus "/dev/md/d1p2".
From kernel version, 2.6.28 the "non-partitioned array" can actually be partitioned. So the "md_dNN" names are no longer
needed, and partitions such as "/dev/mdNNpXX" are possible.
NOTE
mdadm was previously known as mdctl.
mdadm is completely separate from the raidtools package, and does not use the /etc/raidtab configuration file at all.
SEE ALSO
For further information on mdadm usage, MD and the various levels of RAID, see:
http://linux-raid.osdl.org/
(based upon Jakob Ostergaard's Software-RAID.HOWTO)
The latest version of mdadm should always be available from
http://www.kernel.org/pub/linux/utils/raid/mdadm/
Related man pages:
mdmon(8), mdadm.conf(5), md(4).
raidtab(5), raid0run(8), raidstop(8), mkraid(8).
v3.1.2 MDADM(8)
